攪拌車換向閥出現故障怎么辦_公司新聞_新聞資訊_自動攪拌一體車_自動攪拌一體機

站內搜索

新聞資訊

公司新聞行業動態

熱點

自動上料平口攪拌機多種方量可供選擇

2022-12-23

混凝土自動上料攪拌車的功能有哪些？

2022-12-19

混凝土自動拌料車移動式可自行走戶外施工

2022-12-16

自上料攪拌車企業這么多，買車的時候應該看哪方面？

2022-12-12

關于山汽

聯系人：劉老師

電話：400-879-1999

公司：山東山汽工程機械（集團）有限公司

地址：山東省萊州市206國道與308省道交叉口東南50米

攪拌車換向閥出現故障怎么辦

所屬分類：公司新聞發布時間：2021-01-14 來源：http://www.sooezi.com/ 瀏覽量：0

每個城市都會有一定數量的攪拌站，這是因為城市中高樓大廈的建設離不開混凝土，而混凝土的運輸離不開攪拌車，所以攪拌車就顯得非常重要了，攪拌車是由多個部件組成的，比如專用車底盤、上裝罐體、液壓系統、副車架、換向閥等等，其中換向閥也會偶爾出現故障，比如閥不能換向或換向動作緩慢，氣體泄漏，電磁先導閥有故障等等：

Every city will have a certain number of mixing stations. This is because the construction of high-rise buildings in the city cannot do without concrete, and the transportation of concrete cannot do without mixing truck. Therefore, mixing truck is very important. Mixing truck is composed of many parts, such as chassis of special truck, upper tank body, hydraulic system, subframe, reversing valve, etc., among which the reversing valve will occasionally come out For example, the valve can not change direction or the change direction is slow, the gas leaks, and the solenoid pilot valve is faulty

自動攪拌一體車

1. 混凝土攪拌車的換向閥不能換向或者換向動作緩慢，一般是因潤滑不良、彈簧被卡住或損壞、油污或雜質卡住滑動部分等原因引起的。此時，我們應先檢查油霧器的工作是否正常，潤滑油的粘度是否合適。必要時，應更換潤滑油，清洗換向閥的滑動部分，或更換彈簧和換向閥。

1. The reversing valve of concrete mixer can not change direction or the reversing action is slow, which is generally caused by poor lubrication, spring stuck or damaged, oil or impurities stuck sliding part and other reasons. At this time, we should first check whether the oil atomizer works normally and whether the viscosity of the lubricating oil is appropriate. If necessary, replace the lubricating oil, clean the sliding part of the directional valve, or replace the spring and directional valve.

2. 攪拌車的換向閥經長時間使用后容易出現閥芯密封圈磨損、閥桿和閥座損傷的現象，導致閥內氣體泄漏，閥的動作緩慢或不正常換向等故障。此時，需要更換密封圈、閥桿和閥座，或將換向閥換新。

2. After being used for a long time, the reversing valve of mixer truck is prone to wear of valve core sealing ring, damage of valve stem and valve seat, resulting in gas leakage in the valve, slow action or abnormal reversing of the valve. At this time, the sealing ring, valve stem and valve seat need to be replaced, or the change-over valve needs to be renewed.

3. 若電磁先導閥的進、排氣孔被油泥或其他雜物堵塞，封閉不嚴，活動鐵芯被卡死，電路有故障等，均可導致換向閥不能正常換向，對于前三種情況應清洗先導閥及活動鐵芯上的油泥和雜質，而電路故障一般又可分為電路故障和電磁線圈故障兩類。

3. If the inlet and exhaust holes of the solenoid pilot valve are blocked by oil sludge or other debris, the sealing is not tight, the movable iron core is stuck, and the circuit is faulty, the reversing valve can not be normally reversed. For the first three cases, the oil sludge and impurities on the pilot valve and movable iron core should be cleaned, and the circuit faults can be divided into circuit faults and solenoid coil faults.

在檢查電路故障之前，要先將換向閥的手動旋鈕轉動幾下，看換向閥在額定的氣壓下是否正常換向，若能正常換向，則是電路有故障；檢查時，可以用儀表測量電磁線圈的電壓，看是否達到了額定電壓，如果電壓過低，應進一步檢查控制電路中的電源和相關聯的行程開關電路。

Before checking the circuit fault, turn the manual knob of the directional valve a few times to see whether the directional valve can change direction normally under the rated air pressure. If it can change direction normally, the circuit is faulty. When checking, use the instrument to measure the voltage of the solenoid coil to see whether it reaches the rated voltage. If the voltage is too low, further check the power supply and related lines in the control circuit The circuit of the range switch.

如果在額定電壓下換向閥不能正常換向，則應檢查電磁圈的接頭是否松動或接觸不實，檢查方法：拔下插頭，測量線圈的阻值（一般應在幾百歐姆幾千歐姆之間），如果阻值太大或太小，說明電磁線圈已損壞，需要更換。

If the reversing valve can not change direction normally under the rated voltage, check whether the connector of the solenoid coil is loose or not. Check method: pull off the plug and measure the resistance of the coil (generally between several hundred ohm and several thousand Ohm). If the resistance is too large or too small, it means that the solenoid coil is damaged and needs to be replaced.

上一頁：多功能攪拌車出現異常我們該如何做？下一頁：如何選擇自動攪拌一體車的配件呢？

熱門產品 / HOT PRODUCT